Table Pedestal Base Indoor Cast Iron Restaurant Table Base 720mm
- Model
- TB004
Item specifics
- Material
- cast iron
- Finishing
- powder coating
Review
Description
Model TB004 is a cast iron table pedestal base built for commercial indoor use. It stands 720 mm high on a 410 x 410 mm footprint, carries a 250 x 250 mm top plate, and is matched to round tops from 400 to 500 mm. The matte black powder coating is applied over solid cast iron, so the base holds its finish through daily service in restaurants, cafes and bistros. Buyers usually reach this page looking for a metal table base that will not wobble under a loaded top. The weight is the short answer: at 17 kg the base resists tipping when a diner leans on the table edge, which is the failure mode that ends the life of most lightweight pedestal table bases. Four properties that decide whether a commercial table base survives its first year. Mass in the foot is what stops a table tipping. Cast iron delivers it without a wider footprint that diners would kick. Matte black powder coating resists the scuffing, cleaning chemicals and chair contact that strip painted table bases. The 410 mm square foot is matched to 400 to 500 mm round tops, keeping the base near half the top diameter. Column ships separate from base and top plate, which lowers volumetric freight cost on container quantities. Confirmed production figures for model TB004. The most common sizing mistake is pairing a small base with an oversized top. The working rule used across the commercial furniture trade is that a round table base should measure roughly half the diameter of the top it carries. The intended match for TB004. The 410 mm footprint sits at or just above half the top diameter, giving a stable overhang on every side. Overhang grows and edge loading increases the tipping moment. Move to a larger footprint or a four-prong base rather than forcing this model. 720 mm is standard dining height. Add the thickness of your top to get finished table height, and confirm chair seat height against it. Working out dining versus counter and bar heights? See our guide on counter height vs bar height. Supplied as table bases restaurant operators can pair with their own laminate, solid wood or stone tops. Table bases only, no tops included. A single-column cafe table base frees the floor under the top, which matters when seating density is tight and chairs move constantly. Repeat orders of the same model keep every table in a venue at identical height and finish across phased rollouts. Base and top plate travel together in one carton; the column is packed separately. Bubble wrap protects the coated surfaces in transit. The base arrives complete with the fixings needed to join column, foot and top plate. No drilling or welding is required at the venue. Flat-packing the column away from the foot reduces cubic volume per set, which is the main cost driver on full-container shipments. If TB004 does not suit your top, send the top size and required height and we will return a drawing for a matched base. Other configurations produced in the same factory. TB004 is matched to round tops between 400 and 500 mm. The 410 x 410 mm footprint keeps the base close to half the top diameter, which is the standard stability ratio for round commercial tables. 720 mm, which is standard indoor dining height. Finished table height equals 720 mm plus the thickness of the top you fit. Yes. These are table bases only. Operators and fit-out contractors pair them with their own tops, which is why the 250 x 250 mm top plate is drilled for standard fixing. Cast iron concentrates weight low in the foot. A hollow steel base of the same footprint weighs far less and is easier to tip when someone leans on the table edge. Yes. Height, finish and top plate dimensions are adjustable on OEM and ODM orders. Send your specification and we will confirm it on a production drawing. This model is specified for indoor use. Powder coated cast iron is not rated here for permanent outdoor exposure, so tell us if the tables will sit outside and we will quote a suitable finish. Send your top size, required height, finish and quantity. If TB004 is not the right match for your workpiece, we will prepare a drawing for a base that is.Table Pedestal Base for Indoor Dining and Restaurant Tables
Why Specifiers Choose This Indoor Cast Iron Table Base
17 kg ballast
Powder coated finish
Sized for round tops
Two-part packing
Metal Table Base Specifications
Model TB004 Table base height 720 mm Footprint 410 x 410 mm Top plate 250 x 250 mm Weight 17 kg Round top size 400 to 500 mm Material Cast iron Finish Matte black powder coating Base type Single-column pedestal table base, indoor dining table base Applications Restaurant, coffee shop, cafe, bistro, diner Customization OEM and ODM on height, finish and top plate 
How to Match Base Size to Your Table Top
400 to 500 mm round top
Tops above 500 mm
Height planning
Where This Table Base Is Used
Restaurants and diners
Cafes and coffee shops
Hospitality fit-outs
Packaging and Installation
Split carton packing
Assembly on site
Freight efficiency
Custom drawings
Related Table Bases and Legs
Common Questions About Pedestal Table Bases
What size table top fits this pedestal base?
How tall is the table base?
Are table bases supplied without tops?
Why cast iron rather than steel tube?
Can the height or finish be changed?
Is the base suitable for outdoor terraces?
Request a quotation or a custom drawing
